Home Assistant Connect AUX-2 – the smart home multi-tool: PoE audio streamer, RS-232 control and Bluetooth proxy
Bring your Hi-Fi, AV receiver, TV or solar inverter into Home Assistant with a single PoE cable. Stream CD-quality audio in sync with your smart speakers, control serial gear locally and put Z-Wave in the best spot.
- PoE (802.3af) or USB-C power
- Connection via Ethernet, Wi-Fi
- 3.5 mm port, Music Assistant ready
- 2× RS-232, RS-485 via USB adapter
- USB-A for the Connect ZWA-2 Z-Wave adapter
- Bluetooth LE proxy with a dedicated antenna
- ESP32-S3, built on ESPHome
- Requires Home Assistant; ZWA-2, adapters and cables sold separately
Bring Your Existing Gear Into Home Assistant
Home Assistant Connect AUX-2 is the smart home multi-tool from Nabu Casa, the team behind Home Assistant. It streams CD-quality audio straight to your Hi-Fi or AV receiver, perfectly synced with your smart speakers, controls TVs, receivers, projectors, solar setups and UPSs through its USB and two serial ports, moves your Z-Wave network to the ideal spot in your home and extends Bluetooth coverage with a dedicated antenna.
Audio, serial, Z-Wave and Bluetooth all work at the same time. Just plug it in and the Home Assistant wizard helps you set it up. A single Power over Ethernet (PoE) cable delivers power and data, with USB-C and Wi-Fi ready whenever you need them – and every purchase funds the development of Home Assistant.
Please note: a Home Assistant system, such as Home Assistant Green, is required to connect and control devices with Connect AUX-2. Connect ZWA-2, the RS-485 adapter and cables are sold separately.
Whole-Home Synced Audio for Your Hi-Fi
Old but still great-sounding audio gear deserves a second life. AUX-2 sends CD-quality audio through its combined 3.5 mm jack – analog or optical S/PDIF – to your amplifier, AV receiver or active speakers and keeps it in sync with your other smart speakers. It is ready for Music Assistant (Sendspin), so local files and streaming services play across the whole home, and it also works with Home Assistant media playback.
Note: the optical S/PDIF output is not a separate square TOSLINK port. It is built into the combined 3.5 mm audio jack, which plays analog or digital audio depending on the cable you plug in (one at a time). For an optical connection, use a mini-TOSLINK to TOSLINK cable (not included) – in digital mode, a red light glows inside the jack.
- TI PCM5122 DAC with 112 dB SNR
- 16-bit / 48 kHz stereo, lossless digital output
- FLAC, MP3 and WAV playback
- Seamless control – power and volume of supported equipment over a serial cable
Deep Control With RS-232 and RS-485
Plug a serial cable into your TV, AV receiver, projector or any other RS-232 device and control it privately and locally – even in standby, when network control is often not available. Two 3.5 mm RS-232 ports and RS-485 through a USB adapter also bring solar inverters, home batteries, UPSs and other serial gear into your Home Assistant dashboards and automations.
- 2× RS-232 (3.5 mm, ±5 V) with TX/RX switch
- RS-485 via a Waveshare USB-to-RS-485 adapter (sold separately)
- Typical uses: TVs, AV receivers, projectors, solar setups and UPSs
Z-Wave Anywhere With Connect ZWA-2
The best place for your server is rarely the best place for your Z-Wave network. Plug Home Assistant Connect ZWA-2 into the USB-A port of AUX-2 and power both with PoE – the antenna can then sit anywhere in your home with a network connection, right in the middle of your Z-Wave devices.
Connect ZWA-2 and the Ethernet cable are sold separately.
Rock-Solid Bluetooth Proxy
Replace your Bluetooth hub. A dedicated antenna brings sensors and other Bluetooth smart home devices into Home Assistant over a stable wired connection and extends coverage to rooms your server cannot reach.
- Bluetooth 5 LE proxy
- Up to 3 active connections at the same time
- Bluetooth audio is not supported
Powerful Options: PoE, USB-C, Ethernet or Wi-Fi
Power and data run over a single Power over Ethernet cable (802.3af or better) for a clean installation next to your rack, under the TV or in the technical room. Without PoE, simply power AUX-2 via USB-C (5 V, 2 A) and connect it over Ethernet or 2.4 GHz Wi-Fi. Typical power draw is under 1 W.
- Power your way: Power over Ethernet or USB-C
- Flexible connection: Ethernet or Wi-Fi
Built to Be Tinkered With, Reliable to the Core
AUX-2 is built on ESPHome around an ESP32-S3 with 8 MB PSRAM and 8 MB flash. It is easy to take apart and the bootloader is unlocked, so it accepts custom firmware – use it ready out of the box or customise it to your needs. A Grove port on the front panel is there for your own projects.
Designed by Nabu Casa, with dedicated support and years of software updates. Every purchase funds the development of Home Assistant. See more devices that work with Home Assistant and the complete Home Assistant hardware range.